ASTM C – 03 Estimate of the Heat Gain or Loss and the Surface Temperatures of This standard is issued under the ﬁxed designation C ; the number. This standard is issued under the fixed designation C ; the number 1 This practice is under the jurisdiction of ASTM Committee C on Thermal. Insulation . 23 Feb Already shared in my big collection, check there for more. C Standard Practice for Estimate of the Heat Gain or Loss and the Surface.
|Published (Last):||5 December 2015|
|PDF File Size:||6.15 Mb|
|ePub File Size:||5.13 Mb|
|Price:||Free* [*Free Regsitration Required]|
The Eng-Tips staff will check this out and take appropriate action. We have no amendments or corrections for this standard. The computer controls the terminal interactively with program-generated instructions and questions, which prompts user response.
Link to Active This link will always route to the current Active version of the standard. Historical Version s – view previous versions of standard. The use of this practice by both manufacturers and users of thermal insulation will provide standardized engineering data of sufficient accuracy for predicting thermal insulation system performance. This type of analysis is often made prior to system upgrades or replacements.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Therefore, no SI version of the practice has been prepared, because a standard SI equivalent of this practice would be complex. Standards Subsctiption may be the perfect solution. In addition, it has been demonstrated that this practice can be used to calculate heat transfer for circumstances other than insulated systems; however, these calculations are beyond the scope of this practice.
No conflict exists with such modifications as long as the user verifies the modifications using a series of test cases that cover the range for which the new method is to be used. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
This standard is not included in any packages.
ASTM C – Heat Transfer & Thermodynamics engineering – Eng-Tips
Computers are readily available to most producers and consumers of thermal insulation to permit the use of this practice. Qstm this system, intermediate output guides the user to make programming adjustments to the input parameters as necessary. When an international standard for piping and insulation sizing occurs, this practice can be rewritten to meet those needs.
This data is presented for typical insulation thicknesses, operating temperatures, surface orientations facing up, down, horizontal, verticaland in the case of pipes, different pipe sizes. The computer program is intended for flat slab, pipe and hollow sphere insulation systems. The range and quality of the physical and thermal property data of the materials comprising the thermal insulation system limit the calculation accuracy.
As the voice of the U. The same holds for increasing pipe OD. With the existence of radiation and convection modes of heat transfer, the measured value should be called apparent thermal conductivity as described in Terminology C Certain applications may need specific data to produce meaningful results.
This cost can be substantially reduced by the use of accurate engineering data tables, or available computer analysis tools, or both. The equations used in Practice C analysis yield “averaged” results for the entire surface in question.
Students Click Here Join Us! In the spherical coordinate system, Practice C can be applied to radial heat flows to or from stored fluids such as liquefied natural gas LNG. Also, additional calculations may be desired to include other data such as system costs or economic thickness. Download Now The Architecture, Engineering and Construction AEC industry is constantly looking for process improvements to better manage potential project delays and costs.
In it is stated that the standard has for convective coefficient the following for pipes: If the document is revised or amended, you will be notified by email. Air blowing across real objects often follows flow directions and velocities much different from the direction and velocity of the main free stream. For example, the condensation of the gaseous portions of thermal insulation in extremely cold conditions will have an extremely influential effect on the apparent thermal conductivity of the insulation.
The exterior surface temperature of the insulation is often shown to provide information on personnel protection or surface condensation. Few production environments have the luxury of ordering new equipment to replace existing machines on their shop floor.
Register now while it’s still free! Please first log in with a verified aastm before subscribing to alerts.
Resources Few production environments have the luxury of ordering new equipment to replace existing machines on their shop floor.
Promoting, selling, recruiting, coursework and thesis posting is forbidden. Click Here to join Eng-Tips and talk with other members! The wind part is what I want to confirm.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the astmm of regulatory limitations prior to use.
Thanks for replies in advance. Close this window and log in. By joining you are opting in to receive e-mail.